A render lands in the inbox with pretty foil on an empty box, usually lit from one side, logo sitting dead centre on the lid. Looks finished. The PDF that follows is the print file, plus a line that says “add foil”, or “matte film and a bit of spot UV”, and the lid faces are still blank. For gift box finishes, mark those faces and the areas in the first email, before we quote a printed sample.
HangPeng makes custom gift boxes in Yiwu, and lamination, foil and spot UV come up on those box briefs. We run printing, a laminator, a foil stamping machine, creasing and die-cutting on the floor. That is not a catalogue copied from bag briefs. We already compared those finishes on bags in our note on gift bag finishes. This page stays on how to brief the face of a box.

Mark where each finish sits
We still get the one-line version. “Foil logo.” That’s it. The lid is unmarked, the sides are unmarked, the base is unmarked. “Laminate the box” is the other one, and it does not tell us if you mean the lid top only, or the lid and the base, or the wrap on every face. Write the faces down: lid top, lid walls, base walls, and the base bottom if that face shows.
Stops short of an edge? Write that too. A phone photo of a sketch, or of a box already on your shelf, with a line drawn on the lid, is enough to start.
“All over” causes trouble. Some buyers mean the whole lid top. Some mean every face of the closed box. A few mean only the panel around the logo. Name those faces. If you already have a box in hand, photograph the lid, one long side and one end, and mark the areas on those pictures.
We are not posting a coverage chart, a foil-area size list, or a lamination thickness. Show the area. We’ll tell you on the quote if that layout is workable, and look at it again on the sample.
Say how the finish meets the print
Print and foil often share one lid. A film, if you want one, usually sits over the printed wrap. Spot UV, when a buyer asks for it, is usually aimed at a printed area, or at the edge of one. The brief has to say what happens where they meet, or we guess, and guessing is how we waste a sample.
Does the print run up to the edge of the foil and stop? Does the foil sit on a printed colour, or on an unprinted patch? Is the logo foil only, with no ink under it? We have opened files that looked complete, then found the buyer wanted a foil monogram on a printed lid, and neither point was in the email.
Got the meeting edge already decided? Put it in one line next to the artwork. If that part is still open, send the file anyway and tell us the look you want on the logo or the panel; we’ll come back on the quote with what that job can take. Don’t look here for a house rule on whether print goes down before foil, or after lamination, or in some other order. That belongs on the quote and on the sample for this box, not in a general page.

Renders lie about colour once foil or a film is on the wrap. We have had lids come back warmer than the proof, and others look flatter than anyone expected. Send a Pantone for the printed area if you have one. For foil, a swatch beats a colour name. “The same gold as last year’s bag” only helps if that bag is still in our file, or you post us a piece of it.
What to write for lamination, foil and spot UV
Brief lamination, foil and spot UV one at a time if you want more than one. Skip any of them. A printed box with no extra finish is a real option; we will not add a film just because the render had one.
Lamination. If you want a film on the wrap, say matte, gloss, or none. If you already like the feel of a box on your shelf, send a photo, or send the box. We are not publishing a film thickness. The film, if any, is confirmed on the quote and checked on the sample.
Foil. Mark the artwork it covers: a logo, a line, a monogram, a small panel. Tell us the colour you are aiming for, in plain language or with a swatch. We have a foil stamping machine, and we quote foil on boxes when the brief is clear. We will not invent a foil-type list. Fine type and large solid panels are the two places we look carefully on the sample.
Spot UV. Buyers ask for it on boxes as well as on bags. Tell us where you want the varnish: a logo, a pattern, a panel, a line. We’ll confirm on the quote whether we can supply that finish on this box, and we’ll check it on the sample. Do not treat a bag page as a locked yes for a box.
If you already want more than one of these on the same box, name each one next to its area, in the same email. Other effects come up too. Write those down and send a photo or a swatch. We’ll say on the quote what we can follow, rather than invent a yes or a no on a general page.
The structure of the box still needs its own brief
A finish brief does not replace the box brief. Size, structure and how the lid sits still belong in the same email. If you are still choosing a rigid box or a folding box, start with our comparison of rigid and folding gift boxes. For a two-piece box, see our note on lid and base gift boxes. A one-piece fold is a different job; that brief is in one-piece gift boxes.
If you already want a tray, a sponge, or raffia inside, say so in the first email. That briefing is in our note on gift box inserts. This article stays on the face finishes.
We are not posting a board thickness, a wrap weight, or a standard size chart. Those are confirmed on the quote and checked on the sample.
Check the sample with your hands, and with the product in the box
For an ordinary gift box we usually quote a custom sample in 7 to 10 days and bulk in 15 to 20 days after approval, depending on quantity. A finish outside the ordinary run may need a different window, so we’ll confirm both timings on the quote. Prices are EXW Yiwu.
A plain stock box sample, if we have a size close enough to look at, goes out free, freight collect. A printed custom sample, including one with lamination, foil or spot UV, is quoted. A free stock box is not a custom-size sample, and not a finished sample.
When the sample arrives, don’t judge it only on a desk under one light. Tilt the lid. Look at the foil next to the print, and at the edge where they meet. Run a hand across the film, if there is a film. Pack the real product, tissue and all, then put the lid on and look at the faces you marked. If the pack has to travel, put the closed sample in the shipper you actually use.
If a finish sits in the wrong place, or the meeting edge looks messy, fix it on the sample. Catching it after bulk has started costs more, and eats the calendar.
What to send for a gift box finish quote
Custom gift boxes start at 1,000 pieces per order. The sample fee is refunded once that gift box order reaches 1,000 pieces.
Send us:
- Where each finish sits: which faces, a logo, a panel, a line, or a marked photo
- How each finish sits with the print, if you already know
- Lamination: matte, gloss, or none, if you already have a preference
- Foil: the area, and a colour or a swatch if you have one
- Spot UV: the area, if you want us to quote it
- A swatch or a photo of a box face you want us to follow, if you have one
- The box structure and size, with a note on how you measured them, and what goes inside
- Artwork, or a brand direction
- Quantity and the date you need the goods in hand
Envíe un correo electrónico a aaron@yc-gift.com o pengtaolou97@gmail.com, un mensaje de WhatsApp al +86 130 5899 5000 o utilice nuestro página de contacto. Look at how we build cajas de perfume and garment boxes, or browse the box range, for a sense of the other box work we do. This article stays on the finish brief.
Preguntas frecuentes
What is the MOQ for gift boxes with foil or lamination?
1,000 pieces. That is our gift box minimum, and it applies when the brief includes these finishes as well.
Do you publish a foil size list or a lamination thickness?
No. Area, film and the way a finish meets the print are confirmed on the quote and on the sample for the box you brief. There is no coverage chart on this page, and no standard finish catalogue for boxes.
Do I put foil and spot UV on the same lid?
If you want both, mark each area in the same email and say how they sit with the print. We’ll tell you on the quote what we can follow on this box, and we’ll check the meeting edges on the sample. This page does not lock a combination as a house standard.
Do bag finishes automatically apply to gift boxes?
No. The bag article is for bags. Lamination and foil come up on box briefs, and we quote them when the areas are clear. Spot UV and any other effect are confirmed on the quote for the box in front of us, not copied across from a bag page.
How long does a gift box with these finishes take?
We’ll confirm the sample and bulk timing on the quote once the finish areas are agreed. An ordinary gift box is often 7 to 10 days for a sample and 15 to 20 days for bulk after approval, depending on quantity. Don’t treat those figures as a promise until this box is agreed.
Do you send a finished sample I can hold and pack?
A printed custom sample, including one with lamination, foil or spot UV, is a quoted item. If we have a plain stock box close enough in size to be worth looking at, we send that at no charge and you pay the freight; that stock box is not a finished sample. Put the real product in the custom sample when it arrives. Look at the faces and the edges, then close the lid.

