HOGAR > NOTICIAS > Noticias del sector>

Custom Lid-and-Base Gift Boxes: How to Brief Lid Fit and Height

Custom Lid-and-Base Gift Boxes: How to Brief Lid Fit and Height
20 Nov, 2026

We see this one a lot. The render shows a tidy lid on an empty base. The product goes in, and the lid either will not come down or sits up and leaves a gap. Usually the email only had an outside size, and nothing about how tall the piece is once it is in the base. For lid and base gift boxes, put the inside size, any outside limit you already have, the product’s length, width and height, and how you want the lid to sit into the first email, before a board is cut.

HangPeng makes custom lid-and-base gift boxes in Yiwu, and we work from that kind of brief. The render still helps. It does not replace those measurements.

Concept schematic of a two-piece lid-and-base gift box with the lid hovering over the base, example only, not a production specification
Concept schematic, not a production specification. Example lid and base only; not a factory standard and not to scale

This brief is a two-piece box, lid and base

Call it lid-and-base, a two-piece rigid box, or a telescoping lid. What we need to know is that the lid is made as one part, the base as another, and later the two get paired. The lid slides over the base. That is the structure this article covers.

A one-piece fold, where the lid, the walls and the base come off a single blank, is a different job. We already wrote a note on one-piece gift boxes. If you are still choosing between a rigid box and a folding box, use our comparison of rigid and folding gift boxes first, then come back. What follows is only the lid-and-base brief.

Magnetic flip-top boxes and book-style boxes come up in inquiries as well. Those are a different structure and a different brief. Don’t drop magnet details into a lid-and-base email and expect us to treat them as part of this box. If that is the structure you want, say so clearly, and we’ll pick it up on the quote.

We are not posting a board thickness, a wrap gsm, or a lid overlap in millimetres, and we will not invent a standard size chart for this style. Board, wrap and the way the lid sits are confirmed on the quote and checked on the sample, for the box you actually brief.

Inside size and outside size are not interchangeable

The first thing we ask is which number you measured. People use “the size” to mean the inside of the base, or the outside of the closed box, and those two are not interchangeable, because board and wrap sit between them. Paste an inside figure onto the outside line and the box comes up short. Do it the other way around and it comes up large. Say which reading you took.

If a shelf or a carton or a shipper you already use puts a cap on the outside, add that cap in the same email. Then the quote can say whether this product and this lid will squeeze in.

Got a box in front of you that you want us to follow? Measure the inside of the base, then the outside of the closed box. Photograph both with a ruler in the frame, and take a third shot with the lid off. “Same as the last order” is useful only if we still have that order on file. If the only record sits on another supplier’s desk, it is not a size we can work from.

Every so often a buyer asks us to pick a cell off a standard size chart. We have not published one for lid-and-base boxes. Send the product sizes, or the box you want us to follow. We’ll work from that.

Product height and wall height are usually where the brief slips

Height is where a lot of briefs slip. The product’s height, the way it sits, and the wall height of the base have to line up, or the lid ends up somewhere you did not expect. Measure it standing, cap on if the cap stays on in the pack. Lying down is another measurement, and another footprint. A shot from above is a poor source for height. We have had to ask for a side view more than once.

Tell us how you want the lid to sit once the product is in. One buyer wants it down over the base so the edges meet a certain way. The next wants some of the base wall left showing, and sends a photo of a box already on their shelf. We will not invent a millimetre overlap and hang a factory-standard label on it. The sit gets locked on the sample, real product in the base.

Concept schematic of product height against the box wall, with the lid sitting over the base; clearance is set on the sample, no millimetre numbers
Concept schematic, not a production specification. No box size, board thickness or lid overlap is specified; clearance is confirmed on the sample; not to scale

Leave the product a bit of room in the base. The amount is not something we can lock from an email, because it depends on the item, the lid, and whatever else goes in with it. That gap waits for the packed sample. You will not find a millimetre clearance written here. One figure would be wrong for most of the products that come across the desk.

Tissue, a ribbon, a small card left in the box: mention those if they stay with the product. They add height. An insert does too. If you already know you want a paper tray, a sponge, or raffia, say so in the first email and we’ll look at it on the sample. The briefing for those is in our note on gift box inserts. This article stays on the lid, the base and the height.

Check the sample with the real product in the base

For an ordinary gift box we usually quote a custom sample in 7 to 10 days and bulk production in 15 to 20 days after approval, depending on quantity. A construction that sits outside the ordinary run may need a different window, so we’ll confirm both timings on the quote once the brief is clear. Prices are EXW Yiwu.

A plain stock box sample, if we have a size close enough to look at, goes out free, freight collect. A printed custom sample is quoted. A free stock box is not a custom-size sample, and it is not a printed sample.

When the sample turns up, pack the real product. A paper stand-in hides the height problem, every time. Put the item in the base and try the lid. If the lid rides up on the product, or on the tissue, or on an insert, flag that. See whether it comes off without a fight. Close it. Look at the gap around the sides, and whether the sit looks even from the front and from the end. If the pack has to travel, one closed sample in the shipper you actually use will show whether the lid shifts.

If the fit is tight, loose, or just sitting wrong, fix it on the sample. The same problem found after bulk has started costs more, and the days are gone.

What to send for a custom lid-and-base gift box quote

Custom lid and base gift boxes start at 1,000 pieces per order. The sample fee on a gift box is refunded once that order reaches 1,000 pieces.

Send us:

  • Inside size, and an outside limit if you already have one, with a note on which you measured

  • Length, width, height and weight of the product, plus a photo, and whether it stands or lies down

  • How you want the lid to sit, or a photo of a box you want us to follow

  • An insert type if you already know you need one

  • Artwork, or a brand direction

  • Quantity and the date you need the goods in hand

Envíe un correo electrónico a aaron@yc-gift.com o pengtaolou97@gmail.com, un mensaje de WhatsApp al +86 130 5899 5000 o utilice nuestro página de contacto. You can also look at how we build cajas de perfume and garment boxes, or browse the box range, if you want a sense of the other box work we do. This article stays on the lid-and-base brief itself.

Preguntas frecuentes

What is the MOQ for lid-and-base gift boxes?

1,000 pieces. That is our gift box minimum, and it applies here.

Do I send an inside size or an outside size?

Send both if you have them, and say which is which. Inside size is the space the product lives in. Outside size is the closed box. If you only have one, tell us how you measured it. If a shelf or a shipper caps the outside, put that limit in the same email.

Do you publish a lid overlap or a board thickness?

No. Board, wrap and the way the lid sits are confirmed on the quote and on the sample for the box you brief. There is no published overlap in millimetres, and there is no standard size chart for this style on our site.

Does it matter whether the product stands or lies down?

Yes. Those two positions give you a different height and a different footprint. Say which way the item sits, and measure it that way, cap on if the cap stays on in the pack.

How long does a lid-and-base gift box take?

We’ll confirm the sample and bulk timing on the quote once the lid fit is agreed. An ordinary gift box is often 7 to 10 days for a sample and 15 to 20 days for bulk after approval, depending on quantity. Don’t treat those figures as a promise until this box is agreed.

Is a magnetic flip-top the same brief?

No. A magnetic flip-top is a different structure. A book-style box is too. If that is what you want, say it plainly in the email and attach a photo or a sketch. Mixing those details into a lid-and-base brief just means we stop and ask which box you actually mean.

`
Productos
Contactos
WhatsApp
Correo electrónico